Product Quick Selection Wheel

QUATTRO SERIES QUATTRO - Victron Inverter Charger

Features
  • 3kVA to 15kVA Inverter Charger
  • Lithium Ion battery compatible
  • Two AC inputs with integrated transfer switch
  • Two AC Outputs with no-break functionality
  • Virtually unlimited power through parallel operation
  • Three phase capability
  • PowerControl for limited generator or grid power
  • PowerAssist boosting shore or generator power
  • Solar energy AC power available even during grid failure
  • On-site monitoring and control
  • Remote monitoring and Control

QUATTRO - Victron Inverter Charger

Product Overview

QUATTRO Inverter/Charger 3kVA - 15kVA  

Multifunctional Similar to the MultiPlus, the Quattro is also a combined inverter and charger. Additionally it can accept two AC inputs and automatically connect to the active source. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology plus multiple system integration features such as three or split phase operation and parallel operation. Models: 3000VA, 5000VA, 8000VA, 10000VA and 15000VA

Two AC Inputs & two AC Outputs  The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output..

Unique PowerAssist feature  The Quattro will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery.

Virtually unlimited power thanks to parallel operation   Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 54 kW / 60 kVA output power and 840 Amps charging capacity.

Three phase capability   Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 162 kW / 180 kVA inverter power and more than 2500 A charging capacity.

PowerControl – Dealing with limited generator, shoreside or grid power   The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shoreside supply (16 A per 5 kVA Quattro at 230 VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded.

Solar energy: AC power available even during a grid failure   The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available.

System configuring   - In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. - Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. - Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications).

On-site Monitoring and control   Several options are available: Battery Monitor, Multi Control Panel, Ve.Net Blue Power panel, Color Control panel, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).

Remote Monitoring and control   Victron Ethernet Remote, Victron Global Remote and the Color Control Panel. Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.

Remote configuring   When connected to the Ethernet, systems with a Color Control panel can be accessed and settings can be changed.

Specifications

INVERTER
Input voltage range 9.5-17Vdc, 19-33Vdc, 38-66Vdc
Output voltage 230Vac +/-2%
Frequency 50Hz +/-0.1%
Output Power See selection table
CHARGER
Charge Voltage 'Absorption' 14.4V, 28.8V, 57.6Vdc
Charge voltage 'Float'

13.8V, 27.6V, 55.2Vdc

Charge voltage 'Storage'

13.2V, 26.4V, 52.8Vdc

Charge current house battery

See selection table

Charge current

starter battery

4A (12V & 24V models

Battery temperature

sensor

Yes

PROTECTION
Output overload or short circuit

Yes

Battery voltage too high or too low

Yes

Temperature too high

Yes

Input voltage ripple too high

Yes

STANDARDS AND APPROVALS
Safety EN-IEC 60335-1, EN-IEC 60335-2-29,

EN-IEC 62109-1

Emission, Immunity

EN 55014-1, EN 55014-2, EN-IEC 61000-3-2,

EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2,

IEC 61000-6-3

Road vehicles 12V and 24V models: ECE R10-4
ENVIRONMENT
Operating Temp

-40 to +65C

Refer to inverter output power in selection table

Humidity

95% (non condensing)

GENERAL
PowerControl

Yes, all Quattro inverter/charger models

Integrated Transfer switch

Yes, all Quattro inverter/charger models

AC inputs (2x)

Input voltage range: 187-265 VAC

Input frequency: 45 – 65 Hz

Power factor: 1

Maximum feed through current

3kVA, 2 x 50A

5kVA ot 15kVA, 2 x 50A

PowerAssist

Yes, all Quattro inverter/charger models

Parallel & 3ph operation

Yes, all Quattro inverter/charger models

Programmable relay

Can be set for general alarm, DC undervoltage or genset start/stop function

AC rating 230V/4A

DC rating 4A up to 35Vdc, 1A up to 60Vdc

VE Bus Communications

For parallel and three phase operation, remote monitoring and system integration

General Purpose Com Port

2 ports

Remote on-off

Yes

Auxillary output

3kVA: (25A)

5kVA to 15kVA: (50A)

Digital Multi Control

A convenient and low cost solution for remote monitoring, with a rotary knob to set Power Control and Power Assist levels

Blue Power Panel

Connects to a Multi or Quattro and all VE.Net devices in particular the VE.Net Battery Controller. Graphic display of current and voltages

BMV Battery Monitor

The BMV Battery Monitor features an advanced microprocessor control system combined with high resolution measuring systems for battery voltage and charge/discharge current. The Software includes complex calculation algorithms, to exactly determine the state of charge of the battery. The BMV selectively displays the battery voltage, current consumed AH or time to go. The monitor all stores a host of data regarding performance and use of the battery

Selection Table

QUATTRO

(INVERTER)

12/3000/120-50/50

24/3000/70-50/50

12/5000/220-100/100

24/5000/120-100/100

48/5000/70-100/100

24/8000/200-100/100

48/8000/110-100/100

48/10000/140-100/100

48/15000/200-100/100

Input Voltage Range  

9.7-17V, 19-33V, 38-66Vdc

   
Output   230Vac +/-2%, 50Hz +/-0.1%      
Cont. output power at 25C 3,000VA 5,000VA 8,000VA 10,000VA 15,000VA
Cont. output power at 25C 2,400W 4,000W 6,500W 8,000W 12,000W
Cont. output power at 40C 2,200W 3,700W 5,500W 6,500W 10,000W
Cont output power at 65C 1,700W 3,000W 3,600W 4,500W 7,000W
Peak Power 6,000W 10,000W 16,000W 20,000W 25,000W
Maximum Efficiency 93 / 94% 94 / 94 / 95% 94 / 96% 96% 96%
Zero load power 20 / 20W 30 / 30 / 35W 45 / 50W 55W 80W
Zero load power in AES mode 15 / 15W 20 / 25 / 30W 30 / 30W 35W 50W
Zero load power in search mode 8 / 10W 10 / 10 / 15W 10 / 20W 20W 30W

QUATTRO

(CHARGER)

12/3000/120-50/50

24/3000/70-50/50

12/5000/220-100/100

24/5000/120-100/100

48/5000/70-100/100

24/8000/200-100/100

48/8000/110-100/100

48/10000/140-100/100

48/15000/200-100/100

Charge voltage 'absorption' 14.4 / 28.8V

14.4 / 28.8 / 57.6V

28.8 / 57.6V 57.6V 57.6V
Charge voltage 'float' 13.8 / 27.6V 13.8 / 27.6 / 55.2V 27.6 / 55.2V 55.2V  55.2V 
Storage mode 13.2 / 26.4V 13.2 / 26.4 / 52.8 V 26.4 / 52.8V 52.8V 52.8V
Charge current house battery 120 / 70A 220 / 120 / 70A 200 / 110A 140A 200A
Charge current starter battery   4A (12V, 24V models)      
Battery temperature sensor   Yes      
MECHANICAL

12/3000/120-50/50

24/3000/70-50/50

12/5000/220-100/100

24/5000/120-100/100

48/5000/70-100/100

24/8000/200-100/100

48/8000/110-100/100

48/10000/140-100/100

48/15000/200-100/100

Material  

Aluminium

     
Colour   Blue RAL5012      
Battery Connection   4 x M8 bolts      
230Vac Connection

Screw Terminals

13mm2 (6 AWG)

Bolts M6

 Bolts M6 Bolts M6 Bolts M6
Weight  19kg

34kg

30kg

30kg

45kg

41kg

51kg 72kg
Dimensions (h x w x d)  362 x 258 x 218mm

470 x 350 x 280mm

444 x 328 x 240mm

444 x 328 x 240mm

 470 x 350 x 280mm  470 x 350 x 280mm  572 x 488 x 344mm

Technical Illustration

Back to Top

Your Sales Enquiry